Current issue: 54(2)
Rut formation caused by logging operations has been recognised as a challenge for Swedish forestry. Frequent traffic with heavy machines on extraction roads, together with a warmer climate, is one of the factors that increases the risk of rut formation in forests. One possible way to control this impact of logging operations is to design and apply decision support tools that enable operators to take sensitive areas into account when planning extraction roads. In this study, 16 different logging sites in south-eastern Sweden were surveyed after clear-cut. Information was collected about extraction roads (i.e. traffic intensity, whether the roads had been reinforced with slash) and ruts. Digital maps such as cartographic depth-to-water (DTW) index and soil type were also examined for any connection to rut positions. Soil type and traffic intensity were found to be significant factors in rut formation, while DTW and slash reinforcement were not. However, the DTW map combined with other information, such as soil type, could contribute to decision support tools that improve planning of extraction roads.
Pruning was performed at midsummer in two genetically homogenous and managed planted silver birch stands in southern Sweden – one aged 9 and one aged 10 years. Wood defects were analysed 10 years thereafter, using the five uppermost twigs of the stems up to a height of 30 dm. The number of trees examined at each site was around 70, of which half were pruned. The main findings were that: a) compared to unpruned trees, pruned trees produced more defect-free wood outside the knots; b) most wood defects were found inside the knots; and c) wood defects like rot and bark ingrowth were similar for pruned and unpruned trees, while discolouration was marginally higher for pruned trees inside knots but similar outside knots. Overall, the results confirm previous findings that pruned birch trees will provide butt logs with higher value than unpruned trees.
In this study, we developed models of transfer effects for growth and survival of Scots pine (Pinus sylvestris L.) in Sweden and Finland using a general linear mixed-model approach. For model development, we used 378 provenance and progeny trials with a total of 276 unimproved genetic entries (provenances and stand seed check-lots) distributed over a wide variety of climatic conditions in both countries. In addition, we used 119 progeny trials with 3921 selected genetic entries (open- and control pollinated plus-tree families) for testing model performance. As explanatory variables, both climatic indices derived from high-resolution gridded climate datasets and geographical variables were used. For transfer, latitude (photoperiod) and, for describing the site, temperature sum were found to be main drivers for both survival and growth. In addition, interaction terms (between transfer in latitude and site altitude for survival, and transfer in latitude and temperature sum for growth) entail changed reaction patterns of the models depending on climatic conditions of the growing site. The new models behave in a way that corresponds well to previous studies and recommendations for both countries. The model performance was tested using selected plus-trees from open and control pollinated progeny tests. Results imply that the models are valid for both countries and perform well also for genetically improved material. These models are the first step in developing common deployment recommendations for genetically improved forest regeneration material in both Sweden and Finland.
Seed orchards are the link between tree breeding and reforestation. This paper presents data on cone, seed and pollen production and seed quality gathered over 21 years in a Pinus sylvestris (L.) experimental seed orchard containing plots with 14 different combinations of stand density and targeted pruning height. The treatments’ stand densities ranged from 267 to 4000 stems ha-1, and the target graft heights ranged from 2 to 6 meters. Pollen production began at the same orchard age for all studied combinations of stand density and target height but the level of pollen production per hectare increased more rapidly in treatments with higher stand densities. In treatments with dense spacing, cone and seed production initially increased more rapidly than in treatments with wider spacing, thereby providing an earlier return on investment and a shorter seed production lag time. However, the levels of cone and seed production in such treatments over the entire study period were not appreciably different to those achieved in treatments with wider spacing and higher target height. The treatments did not differ substantially with respect to seed quality. These results show that comparable levels of seed production can be obtained with different combinations of stand density and target height, giving seed orchard owners and managers a wide range of viable management options.