Current issue: 53(2)
Under compilation: 53(3)
Highest degree of precision in determining the areas of different strata in forest survey is achieved when the areas are measured from a map. However, in practice the stratum-areas usually need to be determined on the basis of samples taken in the field or from aerial photographs. The goal of the present investigation was to determine the precision in stratum-area estimation on the application of different sampling methods.
Three sampling methods were used: 1. sampling with random plots, 2. uniform systematic plot sampling, and 3. sampling with equidistant lines.
The dependence of the standard error of stratum-areas in systematic line and plot sampling was examined by regression analysis. The models for regression equations were derived from random sampling formulae. It appears that the characteristics of these formulae were applicable as variables in the regression equations for systematic samples. Also, some characteristics of the distribution of the stratum was found, which seem to influence the error in sampling with equidistant lines.
The results as regards uniform systematic plot sampling indicate that the use of random sampling formulae leads to considerable over-estimation of the standard error. Nonetheless, unless relatively short intervals between sample plots are used in the forest survey made on the ground, it is of advantage to study the division of the area into strata by measuring the distribution of the survey lines in these strata.
The results can be used in two ways: for estimation of the precision in a survey already made, or to predetermine the sample size in a survey to be made. The results may be applicable to areas ranging from 100 to 1,000 ha in size, as well as to larger areas.
The purpose of this paper is to review tests made on the basis of Finnish material with regard to the efficiency of the 10-point cluster in sampling a stand in forest inventory. Currently, this system is applied in field work in the national forest surveys in the United States of America. The paper reports on tests, made on the basis of Finnish material, for comparison of the 10-point cluster of variable plots with 13 other designs in sampling a stand in forest survey. The research material consists of 12 stands, with Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) H. Karst.) as the main species.
The main results are concerned with the ability of different designs to provide gross volume estimates. As a measure of efficiency, three alternative series of variances were used, adjusted by three alternatives of time. The results are applicable, for instance, in double-sampling with photo and field classifications. In the comparisons, no attention was paid to the possibility of systematic errors in various designs.
For inventory volume, the 10-point cluster proved to be about 10 per cent less efficient than the best design of each alternative. The use of a single circular plot of 1,000 m2 can be recommended under the conditions of this test; furthermore, one or two 500 m2 plots were more efficient than any combination of variable plots.
The reason for the use of the 10-point cluster in forest surveying has been the ability of the design to provide simultaneous information on area condition classes. Among the designs tested, the 10-point cluster seems to be the only one capable of application in the estimation of condition classes.
Most of the information obtained by means of the 10-point cluster can be gained through ocular estimation, and from the sample trees to be measured in any design, but a cluster of several points appears to offer good means of estimation, for instance, of the presence of clumps and gasps in a stand.
The first estimates on the forest resources of Finland were presented in the middle of the 1900th century. The first line survey was conducted in 1912 in Central Finland. In 1921-1923 a survey of the forests of the whole country was commenced. The method consisted in measurement of sample plots in conjunction with ocular estimation of all the stands within the range of the lines. The methods were further developed in the second National Forest Survey in 1936-1938, which payed special attention to the silvicultural condition of the forests, and the growth in the light of climatic variation. When 3.3 million ha of forests were ceded to the Soviet Union in the peace treaty of 1944, the results of the survey had to be recalculated. The next survey was conducted 1951-1953. In this survey, the recovery of stands on drained peatlands was studied. The results of the inventories show that forest resources of Finland had icreased since the 1936-1938 survey.
The first investigation of wood utilization in Finland was carried out in 1927, after the first National Forest Survey had provided information on the forest resources, and knowledge of the other side of the forest balance was desired. The most difficult part was to determine the domestic wood consumption of the rural population. This was accomplished by studying 1,337 sample farms. The second investigation was commenced in 1938, and third in 1954.
These two investigations have made it possible to determine the annual removal and annual growth, and by comparing these results, growth balance. A forest balance is an essential condition for judicious forestry.
The Acta Forestalia Fennica issue 61 was published in honour of professor Eino Saari’s 60th birthday.
The purpose of this study was to test the benefits of a forest site quality map, when applying satellite image-based forest inventory. By combining field sample plot data from national forest inventories with satellite imagery and forest site quality data, it is possible to estimate forest stand characteristics with higher accuracy for smaller areas. The reliability of the estimates was evaluated using the data from a stand-wise survey for area sizes ranging from 0.06 ha to 300 ha. When the mean volume was estimated, a relative error of 14 per cent was obtained for areas of 50 ha; for areas of 30 ha the corresponding figure was below 20 per cent. The relative gain in interpretation accuracy, when including the forest site quality information, ranged between 1 and 6 per cent. The advantage increased according to the size of the target area. The forest site quality map had the effect of decreasing the relative error in Norway spruce (Picea abies) volume estimations, but it did not contribute to Scots pine (Pinus sylvestris) volume estimation procedure.
After the Second World War Finnish Forest Service was faced with large e-mapping and timber surveying project in Northern Finland. The funds for mapping were very limited. In order to re-map the large areas, the only way was to look for alternative methods for the ground methods. The photogrammetric equipment of Finnish Army was made available to the civil service. Consequently, since 1947 several forest mapping projects were carried out in co-operation between the Forest Service and the Army Topographic Service.
When more funds were coming available for the project, new instruments were acquired. The article describes the present mapping procedure and suggests alternative ways in procedure and utilization of new equipment. It concludes that if the forest area under modern timber management plans is several million acres, the ideal implemental framework for mapping and timber surveying unit in Finland should be the following: Radial Secator RS I and slotted templates for the radial line plot, Stereotope Plotter for drafting general maps, the old Delft Scanning Stereoscope for photo interpretation, and Aero-Sketchmaster for transport of the photo details.