Current issue: 55(2)

Under compilation: 55(3)

Scopus CiteScore 2019: 3.1
Scopus ranking of open access forestry journals: 6th
PlanS compliant
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles containing the keyword 'fracture toughness'.

Category: Research article

article id 309, category Research article
Sandhya Samarasinghe, Don Kulasiri, Tristan Jamieson. (2007). Neural networks for predicting fracture toughness of individual wood samples. Silva Fennica vol. 41 no. 1 article id 309. https://doi.org/10.14214/sf.309
Strain energy release rate (GIc) of Pinus radiata in the TL opening mode was determined using the compliance crack length relationship. A total of 123 specimens consisting of four sizes of specimen with each size having four different crack lengths were tested. For each specimen, grain and ring angles, density and moisture content were measured. Video imaging, was used to measure crack length during propagation. Since cracks extended in stages, full compliance-crack length relationship was developed for each specimen based on their initial and subsequent crack lengths. No significant differences in GIc, between initial and subsequent crack lengths were found for the smaller specimens by paired sample t-tests, but differences were significant for the largest specimen size. The Average fracture toughness was calculated from GIc and it was 215 kPa.m0.5. Three artificial neural networks were developed to predict the: 1) force required to propagate a crack, 2) crack extension, and 3) fracture toughness of an individual specimen. Each was successful, producing respective R2 of 0.870, 0.865, and 0.621 on validation data. A sensitivity analysis of the networks revealed that the crack length was the most influential with 21% contribution followed by grain angle with 14% contribution for predicting the applied force. This was followed by volume and physical properties. For predicting the crack extension, density had the greatest contribution (20%) followed by previous crack length and force contributing 16% equally. Fracture toughness was dominated by the dimensional parameters of the specimen contributing (42%) followed by anisotropy and physical properties.
  • Samarasinghe, Centre for Advanced Computational Solutions (C-fACS), Lincoln University, New Zealand ORCID ID:E-mail:
  • Kulasiri, Centre for Advanced Computational Solutions (C-fACS), Lincoln University, New Zealand ORCID ID:E-mail:
  • Jamieson, Centre for Advanced Computational Solutions (C-fACS), Lincoln University, New Zealand ORCID ID:E-mail:
article id 415, category Research article
Sandhya Samarasinghe, Don Kulasiri. (2004). Stress intensity factor of wood from crack-tip displacement fields obtained from digital image processing. Silva Fennica vol. 38 no. 3 article id 415. https://doi.org/10.14214/sf.415
Stress intensity factor of radiata pine (Pinus radiata) in Tangential-Longitudinal opening mode was determined from crack-tip displacement fields obtained from digital image correlation in conjunction with orthotropic fracture theory. For lower loads, experiments agreed with the linear elastic fracture theory but for higher loads, stress intensity factor and load relationship was nonlinear. For 41% of the specimens tested, tip-displacement based stress intensity factor agreed with that based on the ASTM standard formula for lower loads but deviated for higher loads closer to failure. The tip displacement plots showed that the nonlinear behaviour is due to large displacements which we attributed to large plastic deformations and/or micro-cracking in this region. The other 59% specimens showed a similar trend except that the crack-tip based stress intensity factor was consistently higher than the value obtained from the standard formula. The fracture toughness from tip displacements was larger than the standard values for all specimens and the two were related by a logarithmic function with an R2 of 0.61. The study also established that fracture toughness increases with the angle of inclination of the original crack plane to the Radial Longitudinal plane.
  • Samarasinghe, Lincoln University, P.O. Box 84, Canterbury, New Zealand ORCID ID:E-mail:
  • Kulasiri, Lincoln University, P.O. Box 84, Canterbury, New Zealand ORCID ID:E-mail: kulasird@lincoln.ac.nz (email)

Register
Click this link to register for Silva Fennica submission and tracking system.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles

Committee on Publication Ethics A Trusted Community-Governed Archive