Current issue: 58(5)
The objective of this paper was to study the influence of defects of Betula pendula Roth and Betula pubescens Ehrh. on the quality, value and quantity of veneer cut produced by rotary cutting, to prepare grading rules for veneer birch and to determine the minimum quality for veneer birch, and to assess the quality and quantity of veneer yield in rotary cutting of bolts of different grades. Data for the study was collected in 1953-1963 from six plywood factories in Finland.
The effect of knot marks, knot bumps, dry and rotten knots, sound knots, sweep and crookedness, upright limbs, heart rot, open and overgrown scars and bark peeling defects in the bolt on the quality and yield of veneer is described. Recommendations for grading rules were defined on the basis of the result. The rules include three grades, for which certain defects are allowed. In the first grade are accepted bolts, which of the veneer yield included at least 30% of veneer of grades A and B when all jointing and end-clipped sheets were taken into account. In the second grade were accepted bolts, which of the main part of the veneer yield still is surface veneer on the basis of the wood quality. Of the third-grade bolts at least one third of the veneer yield ought to be surface veneer.
The PDF includes a summary in English.
The objective of the study was to establish the influence of the founding density of a stand and the intensity of intermediate cutting on the quality of pine saw logs stems, primarily on their branchiness. Measurements were carried out in 68 Myrtillus-type and 32 Vaccinium-type Scots pine (Pinus sylvestris L.) stands. The quality of 1,982 sample trees was assessed.
According to the results, the branchless part of the stem is longest in the older age classes of trees. In all age classes the percentage of the branchless part is highest in medium sized stems. The relative height of the crown limit is greatest in small diameter classes and continues as the thickness of the tree increases. The crown is longer in the thicker tree. The grade of the butt log is on average highest in medium sized stems. Knottiness of a log made it unsuitable for a saw log only among the thickest stems. The relative share of the u/s grade decreased as the thickness of the trees increased.
From the point of view of early development of the trees it was concluded that in all age classes the branchless part is the shorter the faster the tree has grown in diameter when it was young. Also, branches of the butt log are the bigger the faster the tree has developed when it was young. The grade of the butt log improves as the thickness of the annual rings diminishes.
To produce good quality sawn timber, the pine stands should be established dense, and the first thinnings should be delayed as much as possible. The best time for the thinning would be when the diameter of the dominant trees at stump height is 12–15 cm and when all the branches have died on the length of the butt log. After the first thinning, comparatively intense intermediate thinning may be applied.
The PDF includes a summary in English.
The objective of the present investigation was to clarify the influence of raw material on the quantity, and especially quality of rotary cut birch veneer by running cutting tests with constant tool setting under factory conditions and with bolts of normal size. The quality of the veneer was mainly examined in laboratory.
The result showed that with an increase in bolt size the yield increases and reaches the maximal value in the diameter range of 251–275 mm and 226–250 mm for 60-inch and 50-inch bolt, respectively. With a decrease in bolt length the yield becomes higher. With the increase in the bolt size the quality of the veneer improves.
Defects in the shape of the bolt, such as crookedness, taper and oval form, decrease the yield. The good quality of the bolts affects most the yield of full-size sheets. Increase of knottiness decreases the yield by 4–5%. Lowering of the bolt temperature below 0 °C causes a sharp decline in the yield. Moisture content of the wood did not markedly affect the yield, but it improved the quality of the veneer. The minimum moisture content was 75%.
For the technical quality of the veneer, bolt temperature was the most decisive raw material factor. Also shape defects, of which crookedness was most serious, decreased the technical quality. Increase in summerwood percentage improved the quality.
The PDF includes a summary in English.