Silva Fennica vol. 41 no. 1 | 2007

• Heinonen, University of Joensuu, Faculty of Forestry, P.O. Box 111, FI-80101 Joensuu, Finland E-mail: tero.heinonen@joensuu.fi
• Kurttila, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: mk@nn.fi
• Pukkala, University of Joensuu, Faculty of Forestry, P.O. Box 111, FI-80101 Joensuu, Finland E-mail: tp@nn.fi

The aim of this study was to analyze the occurrence of butt rot damage to Norway spruce in different parts of southern Finland and to quantify the associated loss of quality. The data used in the study are from the 9th National Forest Inventory and consist of 5998 sample plots and 8007 spruce sample trees of saw-timber size. To predict the probability of damage to stands and trees, logistic regression models were constructed. Separate models were made for the whole study area, for the area where the general risk of Heterobasidion root and butt rot damage is high and for the area where the damage frequency is relatively low. In the high-risk area, the probability of damage decreased with increasing elevation and increased with increasing temperature sum. In addition, damage was more common on fertile sites and less common on peatlands; and thick peat layer decreased the risk of damage. The probability of damage was also higher in stands where special or selective cuttings had been carried out. In the sample tree data, the probability of damage increased slightly with increasing diameter and age of the tree. In the low-risk areas, elevation was the only variable that explained the probability of damage to a spruce tree. Site fertility and previous cuttings (more than ten years ago) explained the probability of damage to stands only weakly. For spruce damaged by butt rot, the saw-timber volume was reduced, on average, by 60% both in the high-risk area and in the low-risk area.

• Mattila, The Finnish Forest Research Institute, Joensuu Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: um@nn.fi
• Nuutinen, The Finnish Forest Research Institute, Joensuu Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: tn@nn.fi

Strain energy release rate (G_Ic) of Pinus radiata in the TL opening mode was determined using the compliance crack length relationship. A total of 123 specimens consisting of four sizes of specimen with each size having four different crack lengths were tested. For each specimen, grain and ring angles, density and moisture content were measured. Video imaging, was used to measure crack length during propagation. Since cracks extended in stages, full compliance-crack length relationship was developed for each specimen based on their initial and subsequent crack lengths. No significant differences in G_Ic, between initial and subsequent crack lengths were found for the smaller specimens by paired sample t-tests, but differences were significant for the largest specimen size. The Average fracture toughness was calculated from G_Ic and it was 215 kPa.m^0.5. Three artificial neural networks were developed to predict the: 1) force required to propagate a crack, 2) crack extension, and 3) fracture toughness of an individual specimen. Each was successful, producing respective R² of 0.870, 0.865, and 0.621 on validation data. A sensitivity analysis of the networks revealed that the crack length was the most influential with 21% contribution followed by grain angle with 14% contribution for predicting the applied force. This was followed by volume and physical properties. For predicting the crack extension, density had the greatest contribution (20%) followed by previous crack length and force contributing 16% equally. Fracture toughness was dominated by the dimensional parameters of the specimen contributing (42%) followed by anisotropy and physical properties.

• Samarasinghe, Centre for Advanced Computational Solutions (C-fACS), Lincoln University, New Zealand E-mail: ss@nn.nz
• Kulasiri, Centre for Advanced Computational Solutions (C-fACS), Lincoln University, New Zealand E-mail: dk@nn.nz
• Jamieson, Centre for Advanced Computational Solutions (C-fACS), Lincoln University, New Zealand E-mail: tj@nn.nz

Researchers and professionals in practical forestry have faced problems concerning the regeneration success of Scots pine in natural regeneration near the timberline in North-East Lapland. The aim of the study was to analyze the seedling establishment and seedling height development of Scots pine in seed-tree stands in the area. The average number of living pine seedlings in the study stands was about 1000 ha^–1, but there was considerable variation between the stands. The seedling density was modelled using a multinomial logistic regression with a random factor. Forest site type and the time since seed-tree cutting were the most significant explanatory variables in the model. The probability of reaching the acceptable seedling density was higher on dry site types than on the more fertile ones. The probability increased with the time elapsed since the regeneration activities. Effective temperature sum and the number of intermediate pines also positively affected the probability, but the presence of residual trees negatively. On northern and eastern slopes the probability was lower than on southern and western ones. Seedling height was modelled using a linear mixed model. The age of a dominant seedling was the most positively effective explanatory variable in the height development model. Other positively affecting significant predictors were time since seed-tree cutting, number of intermediate birches, and distance between a seedling and the nearest seed tree. Degree of paludification had a negative effect. The study suggests that the regeneration of Scots pine in North-East Lapland is a relatively slow process.

• Hallikainen, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland E-mail: ville.hallikainen@metla.fi
• Hyppönen, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland E-mail: mikko.hypponen@metla.fi
• Hyvönen, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland E-mail: juha.hyvonen@metla.fi
• Niemelä, Finnish Forest Research Institute, Rovaniemi Research Unit, P.O. Box 16, FI-96301 Rovaniemi, Finland E-mail: jn@nn.fi

Recent changes of climate and land-use are often regarded to affect the European Alpine region substantially and to trigger an increase in the elevation of the upper treeline. The patterns of tree invasion on a subalpine meadow at 1900 m a.s.l. in Sedrun, Canton Grisons, Switzerland, were studied in order 1) to reconstruct the process of tree establishment and tree–growth dynamics in space and time, and 2) to evaluate the influence of site properties, land-use change and climate on these processes. Dendroecological analysis of 105 Norway spruce combined with an assessment of 48 vegetation plots and 17 soil profiles revealed that the trees were established in one main period (1965–1980s), starting 15 years after the abandonment of the agricultural use of the meadow, and that there is a pronounced environmental gradient along the forest-meadow ecotone. Tree establishment and height growth were favoured close to the former forest edge, but all saplings irrespective of their distance to the forest edge and their age showed increased radial growth since 1990, coinciding with a period of higher summer temperatures in the region. Therefore, we conclude that the observed tree-line dynamics in Sedrun are the result of both land-use and climate change: Tree establishment was triggered by the abandonment of the agricultural use of the meadow, and strongly favoured by particularly good growing conditions in a warm decade, which illustrates the sensitivity of conifers near the alpine tree-line to temperature fluctuations.

• Bolli, Swiss Federal Research Institute, Zürcherstrasse 111, CH-8903 Birmensdorf, Switzerland E-mail: jacqueline.bolli@wsl.ch
• Rigling, Swiss Federal Research Institute, Zürcherstrasse 111, CH-8903 Birmensdorf, Switzerland E-mail: ar@nn.ch
• Bugmann, Swiss Federal Institute of Technology (ETH) Zürich, Universitätstrasse 16, CH-8092 Zürich, Switzerland E-mail: hb@nn.ch

We examined the spatial distribution of fine roots at two forest sites that were ploughed 20 (site K1) and 33 years (site K2) before sampling and planted with Norway spruce (Picea abies (L.) Karst.) seedlings. Soil core samples were taken from the tilt and beneath the tilt, the furrow and the intermediate undisturbed soil to a depth of 0.4 m for fine root biomass, length and necromass determinations. Norway spruce fine roots were found throughout the ploughed forest sites. The fine roots were, however, unevenly distributed: the fine root biomass was highest in the tilt (624 and 452 g m^–2 at sites K1 and K2, respectively) and lowest in the undisturbed soil at site K1 (79 g m^–2) and in the furrow at site K2 (145 g m^–2). The estimated average fine root biomass at the ploughed forest sites (268 and 248 g m^–2 at sites K1 and K2, respectively) was, however, similar to those presented in other studies concerning sites that had not been ploughed. In the tilt, a substantial proportion of the fine roots was in the inverted mineral soil horizons and in the new organic horizon above the tilt. Consistent with the fine root biomass findings, the Norway spruce necromass was highest in the tilt but the vertical distribution of the dead roots was different: the necromass was highest in the buried O_BT horizon. The results of this study suggest that at the ploughed forest sites, a substantial part of Norway spruce nutrient and water uptake occured in the tilt during the first 20 or 33 years after plantation.

• Tanskanen, Department of Forest Ecology, P.O. Box 27, FI-00014 University of Helsinki, Finland E-mail: niina.tanskanen@helsinki.fi
• Ilvesniemi, Finnish Forest Research Institute, P.O. Box 18, FI-01301 Vantaa, Finland E-mail: hi@nn.fi

In order to find the best management practices for forest nursery waste composting, organic waste was composted without or with horse manure or urea in six windrows for two years. The windrows were built in four consecutive years during 1999–2002. In 1999, no extra-nutrients were added to the windrow (N99). In 2000, urea fertilizer was used as a nitrogen source (U00). Despite this, the process did not function properly. In 2001, two windrows were built, one (H01) with and the other (N01) without horse manure. Horse manure slightly accelerated the heating process. Consequently, two windrows with more horse manure were built in 2002. One was aerated passively (H02) as earlier windrows, and the other was aerated forcedly (HA02). Horse manure and forced aeration were needed to keep the temperature above 55°C for long enough to ensure microbial hygiene of the material. The degradation of cellulose was greater during the curing stage. Nutrient leaching was low, although the additives increased leaching in conjunction with the inefficient process. The results showed that forest nursery waste alone is ineffective at raising the temperature of the compost, and degrades slowly due to its low nutrient and easily available carbon content. The best management practice for forest nursery waste composting is to use horse manure and aeration to ensure the heating process. Environmental contamination can be avoided by collecting the leachates. Further research is needed to evaluate the usability of the compost.

• Veijalainen, Finnish Forest Research Institute, FI-77600 Suonenjoki, Finland E-mail: amv@nn.fi
• Juntunen, Finnish Forest Research Institute, FI-77600 Suonenjoki, Finland E-mail: mlj@nn.fi
• Lilja, Finnish Forest Research Institute, PO Box 18, FI-01301 Vantaa, Finland E-mail: al@nn.fi
• Heinonen-Tanski, Univ. of Kuopio, Dept. of Environm. Sc., PO Box 1627, FI-70211 Kuopio, Finland E-mail: hht@nn.fi
• Tervo, Finnish Forest Research Institute, FI-77600 Suonenjoki, Finland E-mail: lt@nn.fi

The genetic variability of Scots pine was investigated in six populations from Poland representing two maternal populations and their natural and artificial progenies. Thirteen enzyme systems controlled by 25 allozyme loci were analyzed using starch gel electrophoresis. Progeny populations maintained a high and similar level of genetic variation to that observed in the maternal populations. As expected, much closer genetic relationships were observed between maternal populations and their respective progeny than between the two maternal populations themselves. Progeny populations had the same major alleles, but differed in the number of rare alleles. Therefore, probably not all rare alleles were transferred from the maternal stands to the progenies. In addition, new rare alleles appeared in the progeny populations, possibly as a result of external pollen flow into the maternal populations.

• Kosinska, Department of Human Medical Genetics, Medical University of Warsaw, Oczki 1, 02-007 Warsaw, Poland E-mail: jk@nn.pl
• Lewandowski, Polish Academy of Sciences, Institute of Dendrology, 62-035 Kórnik, Poland E-mail: al@nn.pl
• Chalupka, Polish Academy of Sciences, Institute of Dendrology, 62-035 Kórnik, Poland E-mail: wc@nn.pl

Models of the annual development cycle of trees in boreal and temperate regions were reviewed and classified on the basis of their ecophysiological assumptions. In our classification we discern two main categories of tree development: 1) fixed sequence development, which refers to irreversible ontogenetic development leading to visible phenological events such as bud burst or flowering, and 2) fluctuating development, which refers to reversible physiological phenomena such as the dynamics of frost hardiness during winter. As many of the physiological phenomena are partially reversible, we also describe integrated models, which include aspects of both fixed-sequence and fluctuating development. In our classification we further discern simple E-models, where the environmental response stays constant, and more comprehensive ES-models, where the environmental response changes according to the state of development. On the basis of this model classification, we have developed an operational modelling framework, in which we define an explicit state variable and a corresponding rate variable for each attribute of the annual cycle considered. We introduce a unifying notation, which we also use when presenting a selection of previously published models. To illustrate the various developmental phenomena and their modelling, we have carried out model simulations. Finally, we discuss the ecophysiological interpretation of the model variables, methodological aspects of the empirical development and testing of the models, the introduction of new aspects to the modelling, other closely related models, and applications of the models.

• Hänninen, Plant Ecophysiology and Climate Change Group (PECC), Department of Biological and Environmental Sciences, Box 65, FI-00014 University of Helsinki, Finland E-mail: heikki.hanninen@helsinki.fi
• Kramer, Alterra, P.O. Box 47, 6700 AA Wageningen, The Netherlands E-mail: kk@nn.nl

The business environment and sources of competitiveness in the woodworking industry have changed notably since the 1990s. Wood products are traded globally, and with the increase of trade, abundant forest resources are no longer the main source of sustainable competitiveness. Competition within the woodworking industry is increasing both between European and non-European enterprises, as well as within the EU. Capability to create value-added, making rational strategic choices, and creative usage of intangible and tangible resources have been emphasized as crucial for sustaining woodworking industry competitiveness in higher cost-level countries. Resource-based view (RBV) defines the availability of intangible assets, capabilities and tangible resources, and their heterogeneous combination to form the basis for company success. The objective of this review is to examine the possibilities to employ the RBV to the study of the woodworking industry by combining existing empirical results of the factors of companies’ competitiveness with assessment of the RBV. In the existing literature, strategies implemented in woodworking companies have been approached rather widely, while the role of intangible and tangible resources in building firm-level success has received less focus. In addition, a significant gap exists in linking firms’ financial accounting information with empirical data on their resource-usage and business strategies. In future studies, more information of the effects of these strategic elements on the actual business success of the firms would be needed.

• Lähtinen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: katja.lahtinen@metla.fi

In Fennoscandia, large areas that have not been subjected to pre-commercial thinning (PCT), and thus support dense stands, are becoming suitable for harvesting biomass. However, efficient systems for harvesting biomass from young stands have not yet been developed. In order to optimise biomass harvesting it is here hypothesized that the handling unit should not be a single tree but a corridor area, i.e., all trees in a specific area should be harvested in the same crane movement cycle. Three types of corridor harvesting approaches (using accumulating felling heads for geometric harvesting in two different patterns) were compared in terms of time required to fell a corridor of standardised size. Corridors are defined as strips of harvested areas between conventional strip-roads. Harvests were simulated in two types of stands, first thinning (FT) and delayed PCT stands, in which the spatial positions of the trees had been mapped. The differences in simulated time consumption per corridor were minor when the only variable changed was the corridor pattern. However, there were ca. 2-fold and 3-fold differences in simulated time consumption per corridor between the harvesting approaches for the FT stand and the PCT-stand, respectively. Furthermore, area handling (felling head accumulating all trees corridor-wise, with no restrictions on the accumulated number of trees except for a certain load limit) was found to give up to 2.4-fold increases in productivity compared to a single-tree (reference) approach for the FT stand. In conclusion, the simulation results clearly show the benefits of applying area-harvesting systems in young, dense stands.

• Bergström, SLU, Dept. of Forest Resource Management, SE-901 83 Umeå, Sweden E-mail: db@nn.se
• Bergsten, SLU, Dept. of Forest Ecology and Management, SE-901 83 Umeå, Sweden E-mail: ub@nn.se
• Nordfjell, SLU, Dept. of Forest Resource Management, SE-901 83 Umeå, Sweden E-mail: tn@nn.se
• Lundmark, SLU, Vindeln Experimental Forests, Svartberget Field Station, SE-922 91 Vindeln, Sweden E-mail: tl@nn.se

The harvesting of energy wood from young stands is increasing as the demand for renewable wood fuel is growing. Energy wood consists of stems, tree tops, branches and needles, depending on the size of the trees and the logging method used. The current forest inventory and planning systems used in private forests in Finland do not produce estimates of energy wood components. In stands typical for energy wood harvesting, a large share of energy wood consists of trees smaller than the minimum size for pulpwood. In this study, energy wood was included into the calculation system of compartment inventory, and a procedure for simulating the thinning treatments in young stands was developed. The results for six inventory alternatives and prediction of energy wood were compared with the use of inventory material from 37 young stands that have plenty of energy wood. The measurement of additional stand characteristics and the use of a calibration estimation method was tested, as well as the use of plot-level inventory data instead of stand level data. The results showed that the measurement of the number of trees per hectare, in addition to stand basal area and mean diameter, improved the energy wood estimates. The additional minimum and maximum diameters improved the precision of the estimates, but did not affect bias. The removal estimates were more precise when plot-level data was used, rather than stand-level data. The removal estimates were higher with plot-level data. The results suggest that, in heterogeneous young stands, plot by plot prediction would give more accurate removal estimates than the calculation of a corresponding prediction at the stand-level.

• Tahvanainen, Finnish Forest Research Institute, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: timo.tahvanainen@metla.fi
• Kaartinen, University of Joensuu, Faculty of Forestry, P.O. Box 111, FI-80101 Joensuun yliopisto, Finland E-mail: kk@nn.fi
• Pukkala, University of Joensuu, Faculty of Forestry, P.O. Box 111, FI-80101 Joensuun yliopisto, Finland E-mail: tp@nn.fi
• Maltamo, University of Joensuu, Faculty of Forestry, P.O. Box 111, FI-80101 Joensuun yliopisto, Finland E-mail: mm@nn.fi