Current issue: 58(4)

Scopus CiteScore 2023: 3.5
Scopus ranking of open access forestry journals: 17th
PlanS compliant
Select issue
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles by Franz Holzleitner

Category : Research article

article id 10178, category Research article
Franz Holzleitner, Magdalena Langmaier, Eduard Hochbichler, Bernhardt Obermayer, Karl Stampfer, Christian Kanzian. (2019). Effect of prior tree marking, thinning method and topping diameter on harvester performance in a first thinning operation – a field experiment. Silva Fennica vol. 53 no. 3 article id 10178. https://doi.org/10.14214/sf.10178
Keywords: productivity; time study; harvester; prior tree marking; thinning method; topping diameter; video analysis
Highlights: No effect on harvester performance due to prior tree marking detected; Operator selection versus prior tree marking was assessed; Operator could apply two different thinning methods; Prior tree marking seems to have a positive effect on residual stand damage.
Abstract | Full text in HTML | Full text in PDF | Author Info

The effect of harvester operator tree selection or prior tree marking in thinning operations on satisfactory results and performance has been widely discussed. In harvester operator tree selection, the machine operator decides on the fly which trees are selected to remain or cut. The objective of the study was to analyze the effect of prior tree marking, thinning method and topping diameter on harvester performance in low-diameter thinning operations. The entire thinning operation was captured using video technology. Overall, 2.36 ha divided into 48 plots with 5202 trees were thinned with an average diameter at breast height (dbh) over bark for all plots of between 12.5 and 14.7 cm. In total, 3122 trees were harvested, resulting in 60% removal of stem number over all plots. The harvester achieved a mean productivity of 7.38 m3 PMH0–1 with 1.48 m3 PMH0–1 SEM, with stem volume having the major influence on harvesting productivity. Prior tree marking, topping and thinning method did not significantly affect productivity. Without prior tree marking by the foresters, harvesting removal was shifted toward lower diameters. Within the unmarked plots, 7.0% of the residual trees were damaged compared with 3.2% in marked plots.

  • Holzleitner, University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan-Straße 82/3, A-1190 Vienna, Austria ORCID https://orcid.org/0000-0001-8489-3050 E-mail: franz.holzleitner@boku.ac.at (email)
  • Langmaier, University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Silviculture, Peter-Jordan-Straße 82/3, A-1190 Vienna, Austria; Austrian Research Centre for Forests, Department of Forest Growth and Silviculture, Seckendorff Gudent Weg 8, A-1130 Vienna, Austria E-mail: magdalena.langmaier@bfw.gv.at
  • Hochbichler, University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Silviculture, Peter-Jordan-Straße 82/3, A-1190 Vienna, Austria E-mail: eduard.hochbichler@boku.ac.at
  • Obermayer, University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan-Straße 82/3, A-1190 Vienna, Austria; Agricultural Technical School of Pyhra, Kyrnbergstraße 4, A-3143 Pyhra, Austria E-mail: bernhardt.obermayer@lfs-pyhra.ac.at
  • Stampfer, University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan-Straße 82/3, A-1190 Vienna, Austria ORCID http://orcid.org/0000-0001-9350-2859 E-mail: karl.stampfer@boku.ac.at
  • Kanzian, University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan-Straße 82/3, A-1190 Vienna, Austria ORCID http://orcid.org/0000-0002-1198-9788 E-mail: christian.kanzian@boku.ac.at
article id 1428, category Research article
Gernot Erber, Franz Holzleitner, Maximilian Kastner, Karl Stampfer. (2015). Effect of multi-tree handling and tree-size on harvester performance in small-diameter hardwood thinnings. Silva Fennica vol. 50 no. 1 article id 1428. https://doi.org/10.14214/sf.1428
Keywords: productivity; thinning; energy wood; motor-manual; accumulating harvester head; delimbing
Highlights: Harvesting with the accumulating energy wood head EF28 was studied under small tree dimension (8 dm3) in hardwood thinnings; Reasonable productivity was achieved; Maximum achieved cutting diameter in hornbeam stand was 23 cm and 15% lower than in softwood stands; Head has potential under such conditions.
Abstract | Full text in HTML | Full text in PDF | Author Info

Early thinnings are laborious and costly. Thus forest companies are searching for cost and time efficient ways to carry out this task. The study’s purpose was to determine the productivity of the EF28 accumulating energy wood harvesting head in harvesting small-diameter hornbeam (Carpinus betulus L.) undergrowth trees and evaluate the effect of its multi-tree handling (MTH) capacity on time consumption. The harvester was a wheeled, three-axle Komatsu 911. A time study of 7.1 hours on 19 plots, with a total area of 0.76 ha was conducted. On average, the harvested tree volume was 8 dm³ and the stand density was 2666 trees/ha. The productivity was modelled with MTH conduction, mean diameter at breast height and the number of trees handled per cycle as independent variables. On average, MTH took 27% longer per cycle, increased extracted volume per cycle by 33% and consequently increased productivity with 5.0%. In 71.9% of the cycles more than one tree was handled and if so, dimensions were smaller than in single-tree handling (5.8 cm vs. 12.0 cm). Maximum felling diameter of 23 cm was about 15% smaller than in softwood (according to the manufacturer’s specifications) and the driver didn’t exploit the EF28’s theoretical potential in terms of trees handled per cycle. It can be concluded that the head could significantly improve productivity in small-diameter wood procurement.

  • Erber, Addresses University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan Straße 82/3, A-1190 Vienna, Austria E-mail: gernot.erber@boku.ac.at (email)
  • Holzleitner, Addresses University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan Straße 82/3, A-1190 Vienna, Austria E-mail: franz.holzleitner@boku.ac.at
  • Kastner, Addresses University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan Straße 82/3, A-1190 Vienna, Austria E-mail: maximilian.kastner@boku.ac.at
  • Stampfer, Addresses University of Natural Resources and Life Sciences Vienna, Department of Forest and Soil Sciences, Institute of Forest Engineering, Peter-Jordan Straße 82/3, A-1190 Vienna, Austria E-mail: karl.stampfer@boku.ac.at
article id 899, category Research article
Franz Holzleitner, Christian Kanzian, Norbert Höller. (2013). Monitoring the chipping and transportation of wood fuels with a fleet management system. Silva Fennica vol. 47 no. 1 article id 899. https://doi.org/10.14214/sf.899
Keywords: forest fuel; supply chain; monitoring; logistic; fleet management; wood chips
Abstract | Full text in HTML | Full text in PDF | Author Info
Controlling and organizing the complex forest-to-consumer supply chain of wood fuels is a challenging task, especially for the chipping and transport processes. Truck mounted chippers and transport trailer-trucks must be scheduled to minimize delay to be profitable. Job management within the supply chain, including machine activity based controlling, offers a new way to increase efficiency and productivity. However, detailed data are required to detect and analyze potential gaps and improve forest fuel supply. Generally, data regarding the wood fuel supply chain process are obtained from extensive time studies that are based on a specific process step. Although time studies can detect details during the production of forest fuels, they only describe certain time frames. Long-term data that are recorded during the entire year could encompass seasonal and short term effects. This study aims to monitor the forest fuel supply processes (semi-automated), specifically regarding time and fuel consumption. Large data sets were automatically and efficiently gathered with little effort by drivers and operators. Data were recorded with fleet management equipment for more than 14 months. Vehicle data, including GPS data, were logged at an interval of one minute. Data management was conducted in a pre-configured database that contained pre-defined reports and were run by the Institute of Forest Engineering, Vienna. Work step assignments were implemented with Structured Query Language (SQL)-routines by using the raw machine activities data and GPS. The chipping and transport activities of more than 240 loads were analyzed by focusing on fuel consumption, time needed and traffic. The average distance between chipping sites and plants was approximately 54 kilometers. Fuel consumption from transport reached 50 l/100 km. The chipping unit reached a productivity of 12.8 odt/PSH15 and had a fuel consumption of 58 liters per operating hour.
  • Holzleitner, Institute of Forest Engineering, Department of Forest and Soil Sciences, University of Natural Resources and Life Sciences, Peter Jordanstrasse 82/3, 1190 Vienna, Austria E-mail: franz.holzleitner@boku.ac.at (email)
  • Kanzian, Institute of Forest Engineering, Department of Forest and Soil Sciences, University of Natural Resources and Life Sciences, Peter Jordanstrasse 82/3, 1190 Vienna, Austria E-mail: christian.kanzian@boku.ac.at
  • Höller, Institute of Forest Engineering, Department of Forest and Soil Sciences, University of Natural Resources and Life Sciences, Peter Jordanstrasse 82/3, 1190 Vienna, Austria E-mail: norbert.hoeller@boku.ac.at
article id 464, category Research article
Christian Kanzian, Franz Holzleitner, Karl Stampfer, Sarah Ashton. (2009). Regional energy wood logistics – optimizing local fuel supply. Silva Fennica vol. 43 no. 1 article id 464. https://doi.org/10.14214/sf.464
Keywords: logistics; energy wood; transport optimization; GIS
Abstract | View details | Full text in PDF | Author Info
The promotion of electric energy production from solid biomass by the Austrian government has lead to a boom in the construction of new combined heat and power plants. The current total demand for wood chips in the research area for energy purposes is 70 400 m3 of loose volume chips per year. The expected increase in demand due to these new plants is more than 4 times greater than current demand: up to 302 700 m3 of loose volume per year. Even if the energy wood feedstock potential is satisfactory, the design of the supply chain is still unresolved. The aim of this study is to give decision-makers a base for further development. To accomplish this, we designed and tested four different supply scenarios: one for 9 plants and one for 16 plants. The scenarios were developed using a combination of geographic information systems (GIS) and linear programming methods. The results indicate that direct transport of solid fuel wood as round wood and chipping at the plant is the cheapest supply system with a resulting cost of 5.6–6.6 EUR/m3 loose. Using harvesting residues can only be recommended for large plants because of poor fuel quality. In this case, residues would be chipped at or near the landing, piled and transported via self-loading trucks at a cost between 8.4 and 9.1 EUR/m3 loose. In order to meet increasing demand and to ensure a continuous supply, especially during the winter and spring seasons it is necessary to optimize the supply chain by including storage terminals. However, using terminals and increased demand both lead to higher logistical costs. For example, if the total volume is handled via terminals, the average supply costs including storage will increase by 26%. Higher demand increases the costs by 24%.
  • Kanzian, University of Applied Life Sciences Vienna, Institute of Forest Engineering, Peter Jordan Strasse 82, A-1190 Vienna, Austria E-mail: christian.kanzian@boku.ac.at (email)
  • Holzleitner, University of Applied Life Sciences Vienna, Institute of Forest Engineering, Peter Jordan Strasse 82, A-1190 Vienna, Austria E-mail: fh@nn.at
  • Stampfer, University of Applied Life Sciences Vienna, Institute of Forest Engineering, Peter Jordan Strasse 82, A-1190 Vienna, Austria E-mail: ks@nn.at
  • Ashton, Southern Regional Extension Forestry, Forestry Bldg. 4-420, University of Georgia, Athens, GA 30602, USA E-mail: sa@nn.us

Register
Click this link to register to Silva Fennica.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles