Current issue: 58(4)

Scopus CiteScore 2023: 3.5
Scopus ranking of open access forestry journals: 17th
PlanS compliant
Select issue
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles by Yrjö Nuutinen

Category : Research article

article id 23065, category Research article
Pentti Niemistö, Heikki Korpunen, Yrjö Nuutinen. (2024). Harvesting efficiency and understory damage with different cutting methods on two storied stands of silver birch and Norway spruce. Silva Fennica vol. 58 no. 2 article id 23065. https://doi.org/10.14214/sf.23065
Keywords: productivity; thinning; costs; harvesting damage; mixed stand; continuous cover; multistorey forest
Highlights: With careful, well-timed harvesting of overstory birch, it is possible to successfully use initial understory spruce in producing the next tree generation; Preserving understory spruce when cutting overstory birch reduced harvesting productivity by 30% in comparison to unpreserved harvesting; Removal of overstory birch had a positive correlation in cutting productivity but negative correlation in the quality of remaining understory spruce.
Abstract | Full text in HTML | Full text in PDF | Author Info

Uneven-aged forests set certain challenges for cut-to-length harvesting work. It is a challenge to cost-effectively remove larger trees while leaving a healthy understory for regrowth. The study’s aim was to evaluate productivity and costs of harvesting two-storied Silver birch (Betula pendula Roth) and Norway spruce (Picea abies (L.) H. Karst.) stands by creating time consumption models for cutting, and using existing models for forwarding. Damage to the remaining understory spruce was also examined. Four different harvesting methods were used: 1) all dominant birches were cut; 2) half of them thinned and understory was preserved; compared to 3) normal thinning of birch stand without understory; and 4) clear cutting of two-storied stand. Results showed the time needed for birch cutting was 26–30% lower when the understory was not preserved. Pulpwood harvesting of small sized spruces that prevent birch cutting was expensive, especially because of forwarding of small amounts with low timber density on the strip roads. Generally, when taking the cutting and forwarding into account, the unit cost at clear cuttings was lowest, due to lesser limitations on work. It was noted that with increasing removal from 100 to 300 m3 ha–1, the relative share of initial undamaged spruces after the harvest decreased from 65 to 50% when the aim was to preserve them.  During summertime harvesting, the amount of stem damage was bigger than during winter. In conclusion, two-storied stands are possible to transit to spruce stands by accepting some losses in harvesting productivity and damages on remaining trees.

  • Niemistö, Natural Resources Institute Finland (Luke), Natural resources, Kampusranta 9 C, FI-60320 Seinäjoki, Finland ORCID https://orcid.org/0000-0002-9152-2108 E-mail: ext.pentti.niemisto@luke.fi
  • Korpunen, Norsk institutt for bioøkonomi (NIBIO), Division of Forest and Forest Resources, Department of Forest operations and digitalization, Divisjon for skog og utmark, Avdeling for Driftsteknikk og digitalisering, Høgskoleveien 8, 1433 Ås, Norway ORCID https://orcid.org/0000-0001-9749-5684 E-mail: heikki.korpunen@nibio.no
  • Nuutinen, Natural Resources Institute Finland (Luke), Production systems, Yliopistokatu 6 B, FI-80100 Joensuu, Finland ORCID https://orcid.org/0000-0003-3360-4444 E-mail: yrjo.nuutinen@luke.fi (email)
article id 10619, category Research article
Yrjö Nuutinen. (2021). Corrigendum: Comparing the characteristics of boom-corridor and selectively thinned stands of Scots pine and birch. Silva Fennica vol. 55 no. 4 article id 10619. https://doi.org/10.14214/sf.10619
Abstract | Full text in HTML | Full text in PDF | Author Info

Corrigendum

  • Nuutinen, Natural Resources Institute Finland (Luke), Production systems, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: yrjo.nuutinen@luke.fi (email)
article id 10462, category Research article
Yrjö Nuutinen, Jari Miina, Timo Saksa, Dan Bergström, Johanna Routa. (2021). Comparing the characteristics of boom-corridor and selectively thinned stands of Scots pine and birch. Silva Fennica vol. 55 no. 3 article id 10462. https://doi.org/10.14214/sf.10462
Keywords: biomass; forestry; first thinning; geometrical thinning; systematic thinning
Highlights: After boom-corridor thinning (BCT), the number of stems per hectare was higher than that after selective thinning. The number of future crop trees was at the same level; The removal of the simulated intermediate thinnings and clearcutting in BCT treatments was 10–18% higher than in selective thinning. The saw log volumes were at the same level in both treatments.
Abstract | Full text in HTML | Full text in PDF | Author Info

Young, dense forest in Finland and Sweden urgently need to receive first thinning. In such stands, conventional selective thinning methods make the harvester work time consuming and, thus, costly. To make small-sized trees economically competitive as raw material for bioenergy and biorefining, new harvesting technologies and/or thinning methods need to be developed. A potential solution is boom-corridor thinning (BCT), rendering effective cutting work. The aim of this study was to describe and compare the stand structure of two Scots pine stands (Pinus sylvestris L.) and one birch-dominated (Betula pendula Roth with natural downy birch, B. pubescens Ehrh.) stand after BCT and selective thinning at the first thinning phase. Furthermore, simulations were conducted to predict the future stand development after the first thinning treatments. The density of the growing stock was 16–46% higher after BCT treatment than after selective thinning because BCT stands included more small and supressed trees with a dbh < 100 mm. However, the numbers of future crop trees with a dbh > 140 mm per hectare were at the same level in both treatments. The stem volume removal per hectare did not differ between treatments. However, simulation of stand development and intermediate thinning and clearcutting revealed that the total removal volume was 10–18% higher in BCT stands compared to selectively thinned ones. The saw log volumes harvested did, however, not differ between treatments. This study shows that BCT generates stands with higher biodiversity compared to conventional thinning as higher levels of biomass removal can be reached throughout stand rotations.

  • Nuutinen, Natural Resources Institute Finland (Luke), Production systems, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: yrjo.nuutinen@luke.fi (email)
  • Miina, Natural Resources Institute Finland (Luke), Natural resources, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: jari.miina@luke.fi
  • Saksa, Natural Resources Institute Finland (Luke), Natural resources, FI-77600 Suonenjoki, Finland E-mail: timo.saksa@luke.fi
  • Bergström, Swedish University of Agricultural Sciences (SLU), Dept of Forest Biomaterials and Technology, Section of Forest Operations, SE-90183 Umeå, Sweden E-mail: dan.bergstrom@slu.se
  • Routa, Natural Resources Institute Finland (Luke), Production systems, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: johanna.routa@luke.fi
article id 165, category Research article
Yrjö Nuutinen, Kari Väätäinen, Antti Asikainen, Robert Prinz, Jaakko Heinonen. (2010). Operational efficiency and damage to sawlogs by feed rollers of the harvester head. Silva Fennica vol. 44 no. 1 article id 165. https://doi.org/10.14214/sf.165
Keywords: productivity; single grip harvester; feed roller; timber damages; work study
Abstract | View details | Full text in PDF | Author Info
In mechanical cutting, deep damage caused by feed rollers can reduce the yield of good quality timber for the sawmill and plywood industries. Additionally the feeding and energy efficiency of feed rollers are important for the profitability of harvester cutting. The objectives of this study were to compare the damages to sawlogs, as well as the time and fuel consumption of stem feeding with six different steel feed rollers during the processing of stems using a single grip harvester. This study tested two rollers with big spikes, two rollers with small spikes, one roller with studs in v-angle and one roller with adaptable steel plates in the ring of the roller. A highly detailed, and accurate processing and fuel consumption projection was recorded using the harvester’s automated data collector on a log and stem level. The roller adaptable plate averaged, for unbarked sawlogs, the lowest damages of 3.7 mm. While the damages of the roller with big spikes were the deepest with an average of 7.8 mm. For medium stems, volume of 0.35 m3, the range of differences between the maximum and minimum effective feeding time per roller was 6–19%, which would increase the effective time consumption of cutting by 1–3%. Corresponding differences in fuel consumption during total stem processing were in the range of 7–15%. According to this study it can be concluded that the traditional rollers with spikes were most effective in processing and fuel consumption, but at the same time they caused the deepest damages to the sawlogs. The roller type with adaptable steel plates was the most effective for small stems, additionally it also caused the least damage to the sawlogs.
  • Nuutinen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: yrjo.nuutinen@metla.fi (email)
  • Väätäinen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: kv@nn.fi
  • Asikainen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: aa@nn.fi
  • Prinz, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: rp@nn.fi
  • Heinonen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: jh@nn.fi
article id 264, category Research article
Yrjö Nuutinen, Kari Väätäinen, Jaakko Heinonen, Antti Asikainen, Dominik Röser. (2008). The accuracy of manually recorded time study data for harvester operation shown via simulator screen. Silva Fennica vol. 42 no. 1 article id 264. https://doi.org/10.14214/sf.264
Keywords: accuracy of timing; mixed effects models; time studies
Abstract | View details | Full text in PDF | Author Info
The aim of the study was to investigate the effect of work experience on the accuracy and variation of observers recording the operation time of a harvester. A simulated thinning operation using a harvester, shown as video via a television screen in laboratory conditions, was observed by 20 inexperienced students and 10 experienced work study researchers. All the observers timed the different work elements of the harvester work with special fieldwork timers. The duration of different work elements measured by the human observers were compared to the corresponding recordings by the harvester’s automated data collector. Although the inexperienced students made more measurement mistakes than the experienced researchers, the differences in measurement error averages were not statistically significant between the groups. However, the variances of tree specific errors were significantly higher in the measurements done by the students. As inexperienced recorders, the students were not able to properly record short work elements, which lasted a maximum of 4 seconds. Due to systematic measurement errors, there was a large variation in the timing structures of the work elements among all observers. Observers’ skills and experience seems to affect measurement accuracy and thus the derived results, especially in intensive time studies. Therefore, the recorder should receive detailed training and practical experience in timing of different work elements of forest operations. In the future, with the use of automated data collectors time studies with large, detailed and accurate data will be implemented. However, due to the varying timing conditions in the forest, manual data collection is still required because of its greater flexibility.
  • Nuutinen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: yrjo.nuutinen@metla.fi (email)
  • Väätäinen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: kv@nn.fi
  • Heinonen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: jh@nn.fi
  • Asikainen, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: aa@nn.fi
  • Röser, Finnish Forest Research Institute, Joensuu Research Unit, P.O. Box 68, FI-80101 Joensuu, Finland E-mail: dr@nn.fi

Category : Research note

article id 23017, category Research note
Yrjö Nuutinen, Jari Miina. (2023). Effect of boom corridor and selective thinning on the post-treatment growth of young Scots pine and birch stands. Silva Fennica vol. 57 no. 2 article id 23017. https://doi.org/10.14214/sf.23017
Keywords: geometrical thinning; systematic thinning; thinning reaction
Highlights: During the 4–5-year post-treatment period, boom corridor thinning did not result in growth and yield losses compared to selective thinning; Within the boom corridor and selective thinning treatments, the increment of trees at the edge of strip roads or corridors was higher than at those trees located in the middle of strip roads and/or corridors.
Abstract | Full text in HTML | Full text in PDF | Author Info
Boom corridor thinning (BCT) is a harvester’s working method, primarily suitable for dense, unmanaged young stands. The method was first studied in Sweden in the early 2000s. In Finland, the idea has been further developed and studied for Finnish forests. The advantage is in the corridor, where the harvester head can move more swiftly, and there is no need to identify trees to grow as much as when using the traditional selective thinning (Sel) method. Moreover, the method can be conducted without cost-intensive pre-clearing of undergrowth, creating post-stands with higher biodiversity. This study is the sequel to a previous study in which experiments on BCT and Sel were established in 2017–2018. The experiments were remeasured 4–5 years after their establishment, and the effect of BCT treatments of Scots pine (Pinus sylvestris L.) and silver birch (Betula pendula Roth) on the post-treatment growth and growth reaction of individual trees within the treatments was compared to traditional Sel. During the post-treatment period, BCT did not result in growth or yield losses compared to Sel. Within the treatments, the increment of trees at the edge of strip roads or corridors was higher than that of trees located in the middle of strip roads and/or corridors. A longer post-treatment period needs to be studied to analyse the effect of BCT on the total yield and especially the yield of saw logs during the rest of the rotation period.

Register
Click this link to register to Silva Fennica.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles