Current issue: 58(4)

Under compilation: 58(5)

Scopus CiteScore 2023: 3.5
Scopus ranking of open access forestry journals: 17th
PlanS compliant
Select issue
Silva Fennica 1926-1997
1990-1997
1980-1989
1970-1979
1960-1969
Acta Forestalia Fennica
1953-1968
1933-1952
1913-1932

Articles by Tomas Nordfjell

Category : Research article

article id 1546, category Research article
Jussi Manner, Lauri Palmroth, Tomas Nordfjell, Ola Lindroos. (2016). Load level forwarding work element analysis based on automatic follow-up data. Silva Fennica vol. 50 no. 3 article id 1546. https://doi.org/10.14214/sf.1546
Keywords: harvesting; cut-to-length logging; haulage; data gathering; automatic recording; classification algorithm; Hidden Markov Models
Highlights: Recent developments in on-board technology enables automatic collection of follow-up data on forwarder work; Time consumption per load was more strongly associated with Loading drive distance than with extraction distance, indicating that the relevance of extraction distance as a main indicator of forwarding productivity should be re-considered; Data, within variables, were positively skewed with a few exceptions with normal distributions.
Abstract | Full text in HTML | Full text in PDF | Author Info

Recent developments in on-board technology have enabled automatic collection of follow-up data on forwarder work. The objective of this study was to exploit this possibility to obtain highly representative information on time consumption of specific work elements (including overlapping crane work and driving), with one load as unit of observation, for large forwarders in final felling operations. The data used were collected by the John Deere TimberLink system as nine operators forwarded 8868 loads, in total, at sites in mid-Sweden. Load-sizes were not available. For the average and median extraction distances (219 and 174 m, respectively), Loading, Unloading, Driving empty, Driving loaded and Other time effective work (PM) accounted for ca. 45, 19, 8.5, 7.5 and 14% of total forwarding time consumption, respectively. The average and median total time consumptions were 45.8 and 42.1 minutes/load, respectively. The developed models explained large proportions of the variation of time consumption for the work elements Driving empty and Driving loaded, but minor proportions for the work elements Loading and Unloading. Based on the means, the crane was used during 74.8% of Loading PM time, the driving speed was nonzero during 31.9% of the Loading PM time, and Simultaneous crane work and driving occurred during 6.7% of the Loading PM time. Time consumption per load was more strongly associated with Loading drive distance than with extraction distance, indicating that the relevance of extraction distance as a main indicator of forwarding productivity should be re-considered.

  • Manner, The Forestry Research Institute of Sweden (Skogforsk), Uppsala Science Park, SE-751 83 Uppsala, Sweden E-mail: jussi.manner@skogforsk.se (email)
  • Palmroth, John Deere Forestry, P.O. Box 472, FI-33101 Tampere, Finland E-mail: PalmrothLauri@JohnDeere.com
  • Nordfjell, Swedish University of Agricultural Sciences, Department of Forest Biomaterials and Technology, SE-901 83 Umeå, Sweden E-mail: tomas.nordfjell@slu.se
  • Lindroos, Swedish University of Agricultural Sciences, Department of Forest Biomaterials and Technology, SE-901 83 Umeå, Sweden E-mail: ola.lindroos@slu.se
article id 1377, category Research article
Raul Fernandez-Lacruz, Fulvio Di Fulvio, Dimitris Athanassiadis, Dan Bergström, Tomas Nordfjell. (2015). Distribution, characteristics and potential of biomass-dense thinning forests in Sweden. Silva Fennica vol. 49 no. 5 article id 1377. https://doi.org/10.14214/sf.1377
Keywords: bioenergy; GIS; wood fuel; early thinning; small-tree harvesting; biomass potential; biomaterial
Highlights: Biomass-dense thinning forests (BDTF) cover 2.1–9.8 M ha in Sweden, which represents 9–44% of the country’s productive forest land area, depending on the constraints applied; 65% of BDTF area is found in northern Sweden; Analyses revealed a yearly harvesting potential of at least 4.3 M OD t of undelimbed whole trees (3.0 M OD t of delimbed stemwood including tops).
Abstract | Full text in HTML | Full text in PDF | Author Info

Understanding the characteristics of unutilized biomass resources, such as small-diameter trees from biomass-dense thinning forests (BDTF) (non-commercially-thinned forests), can provide important information for developing a bio-based economy. The aim of this study was to describe the areal distribution, characteristics (biomass of growing stock, tree height, etc.) and harvesting potential of BDTF in Sweden. A national forest inventory plot dataset was imported into a geographical information system and plots containing BDTF were selected by applying increasingly stringent constraints. Results show that, depending on the constraints applied, BDTF covers 9–44% (2.1–9.8 M ha) of the productive forest land area, and contains 7–34% of the total growing stock (119–564 M OD t), with an average biomass density of 57 OD t ha–1. Of the total BDTF area, 65% is located in northern Sweden and 2% corresponds to set-aside farmlands. Comparisons with a study from 2008 indicate that BDTF area has increased by at least 4% (about 102 000 ha), in line with general trends for Sweden and Europe. Analyses revealed that the technical harvesting potential of delimbed stemwood (over bark, including tops) from BDTF ranges from 3.0 to 6.1 M OD t yr–1 (7.5 to 15.1 M m3 yr–1), while the potential of whole-tree harvesting ranges from 4.3 to 8.7 M OD t yr–1 (10.2 to 20.6 M m3 yr–1) depending on the scenario considered. However, further technological developments of the harvest and supply systems are needed to utilize the full potential of BDTF.

  • Fernandez-Lacruz, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden ORCID http://orcid.org/0000-0001-9284-8911 E-mail: raul.fernandez@slu.se (email)
  • Di Fulvio, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden; International Institute for Applied Systems Analysis (IIASA), Ecosystems Services and Management Program (ESM), Schlossplatz 1, A-2361 Laxenburg, Austria E-mail: Fulvio.di.Fulvio@slu.se
  • Athanassiadis, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden E-mail: Dimitris.Athanassiadis@slu.se
  • Bergström, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden E-mail: Dan.Bergstrom@slu.se
  • Nordfjell, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden E-mail: Tomas.Nordfjell@slu.se
article id 1312, category Research article
Simon Karl Nils Berg, Tomas Nordfjell, Dan Bergström. (2015). Effect of stump size and timing of stump harvesting on ground disturbance and root breakage diameter. Silva Fennica vol. 49 no. 5 article id 1312. https://doi.org/10.14214/sf.1312
Keywords: Picea abies; scarification; Sweden; stump harrow; Ecorex30; site impact; glacial till soil
Highlights: The ground disturbance and root breakage diameter during conventional stump harvesting on mineral soil were quantified; A function for estimating the disturbed area based on stump size was constructed; Many fine roots were found to be harvested; The total ground disturbance at the site after stump harvesting was similar to that caused by soil scarification.
Abstract | Full text in HTML | Full text in PDF | Author Info

Stump wood is a possible alternative to fossil fuel. Its harvesting, however, disturbs the ground and this has not yet been quantified at stump level. Such disturbance is likely to be dependent on stump size, type of soil and timing of stump harvesting. Therefore, we measured ground disturbance and root breakage diameter at two Norway spruce sites with sandy glacial till soil. The sites were harvested with a fork type head, 6 and 18 months after clear cutting. Measurements were made within 2 weeks of harvest. No difference was found between the two sites. The mean area of disturbed ground was 6.06 (std 3.14) m2 per stump and increased exponentially with stump size. A regression function modelling the relationship was constructed. Unexpectedly, many fine roots where extracted in the harvest. The arithmetic and basal area weighted mean root breakage diameter was 4.6 (std 2.2) and 29.5 (std 17.9) mm, respectively. There seems to be a limited increase in root breakage diameter with increased stump size. The small root breakage diameter is associated with reduced fuel quality and greater nutrient removal. It appears that much of the ground disturbance is associated with the creation of ruts rather than stump harvest per se. Stump harvesting disturbs a larger percentage of the area of a harvested site than mounding. Postponing stump harvest by one year did not decrease the ground disturbance or increase the root breakage diameter. To achieve less disturbance and larger root breakage diameter, probably new stump harvesting technology is required.

  • Berg, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden E-mail: phd.simon.berg@gmail.com (email)
  • Nordfjell, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden E-mail: tomas.nordfjell@slu.se
  • Bergström, Swedish University of Agricultural Sciences (SLU), Department of Forest Biomaterials and Technology (SBT), Skogsmarksgränd, SE-901 83 Umeå, Sweden E-mail: dan.bergstrom@slu.se
article id 1030, category Research article
Jussi Manner, Tomas Nordfjell, Ola Lindroos. (2013). Effects of the number of assortments and log concentration on time consumption for forwarding. Silva Fennica vol. 47 no. 4 article id 1030. https://doi.org/10.14214/sf.1030
Keywords: productivity; time study; forest haulage; forwarders; cut-to-length logging; log extraction; terrain transport
Highlights: We analysed the effects of total and forwarded log concentrations (m3 (100 m)–1) and the number of loaded assortments on forwarding; The combination of the number of loaded assortments and their abundance (i.e. forwarded log concentration) affected time consumption most; This knowledge enables improved efficiency by optimizing number and assortment proportions in the various loads required to forward a stand.
Abstract | Full text in HTML | Full text in PDF | Author Info
Forwarding has been carried out for 50 years, but much is still unknown about this work. Its complexity comes from both stand features and essential decision-making. Forwarding time consumption is influenced by e.g. log concentrations and number of assortments. Traditionally, focus has been on the total log concentration (TLC), referring to all logs at the harvesting site. However, we focused on forwarded log concentration (FLC), the load-specific log concentration which depends on the assortment distribution at harvesting site and the load-specific number of assortments. To evaluate the effects of TLC, number of assortments in a load and FLC on the loading and unloading times, a standardized field experiment was carried out. Pile and load sizes were constant, while TLC and FLC were manipulated by varying the pile distribution on the test path. For all work elements, the time consumption per m3 was significantly affected by the number of assortments that were loaded, but only the “driving while loading” work element was also significantly influenced by TLC. However, when untangling the intercorrelation between tested factors, it was found that the time consumption for driving while loading significantly decreased as a function of FLC and was unaffected by the number of assortments in a load. That FLC influences the forwarding time consumption highlights the need to study the effects of combining various assortment proportions in a load. Such knowledge will enable analysis of the most efficient number and assortment proportions to combine in the various loads required to forward a given stand.
  • Manner, Swedish University of Agricultural Sciences, Department of Forest Biomaterial and Technology, SE-901 83 Umeå, Sweden E-mail: jussi.manner@slu.se (email)
  • Nordfjell, Swedish University of Agricultural Sciences, Department of Forest Biomaterial and Technology, SE-901 83 Umeå, Sweden E-mail: tomas.nordfjell@slu.se
  • Lindroos, Swedish University of Agricultural Sciences, Department of Forest Biomaterial and Technology, SE-901 83 Umeå, Sweden E-mail: ola.lindroos@slu.se
article id 135, category Research article
Ola Lindroos, Marina Henningsson, Dimitris Athanassiadis, Tomas Nordfjell. (2010). Forces required to vertically uproot tree stumps. Silva Fennica vol. 44 no. 4 article id 135. https://doi.org/10.14214/sf.135
Keywords: forest fuels; Picea abies; bioenergy; stump harvesting; machine development; Betula spp.
Abstract | View details | Full text in PDF | Author Info
Stumpwood attracts renewed interest due to increased use of forest biomass for bioenergy. In Nordic countries stumps are generally uprooted with crawler excavators, which have strong cranes (ca. 400 kNm gross lift torque), but are not designed for moving in forest terrain. Their use is based on practical experience with available and tested machine types rather than thorough examinations of requirements, partly due to limited knowledge of force requirements for uprooting of stumps. Therefore, in this work mean and maximum forces required to vertically uproot stumps of Norway spruce (Picea abies) and birch (Betula spp.) were quantified together with the effects of various soil types and uprooting methods. The used excavator’s crane-mounted uprooting device enabled comparisons between usage of solely crane force, and a method in which preparatory loosening forces were applied prior to crane force. Uprooting stumps in single pieces proved difficult; 61% split unintentionally. Force requirements were similar across tree species, increasing curve-linearly with stump diameter, and stumps uprooted in a single piece required more force than split stumps. Preparatory loosening reduced crane force requirements and, surprisingly, less force was required to uproot stumps from a mesic, till soil than from a moist, finer-textured soil. No stump required more than 60 kN crane force and functions for maximum force requirements indicate that powerful harvesters and forwarders (gross crane lifting capacity of 273 and 155 kNm, respectively) should be able to uproot all stumps with ≤ 61 cm and ≤ 32 cm diameter, respectively, in one piece. Larger stumps could be managed if it is acceptable that stumps are split before uprooting.
  • Lindroos, Department of Forest Resource Management, Swedish University of Agricultural Sciences, SE-901 83 Umeå, Sweden E-mail: ola.lindroos@srh.slu.se (email)
  • Henningsson, Komatsu Forest AB, Box 7124, SE-907 04 Umeå, Sweden E-mail: mh@nn.se
  • Athanassiadis, Department of Forest Resource Management, Swedish University of Agricultural Sciences, SE-901 83 Umeå, Sweden E-mail: da@nn.se
  • Nordfjell, Department of Forest Resource Management, Swedish University of Agricultural Sciences, SE-901 83 Umeå, Sweden E-mail: tn@nn.se
article id 134, category Research article
Dan Bergström, Urban Bergsten, Tomas Nordfjell. (2010). Comparison of boom-corridor thinning and thinning from below harvesting methods in young dense Scots pine stands. Silva Fennica vol. 44 no. 4 article id 134. https://doi.org/10.14214/sf.134
Keywords: bioenergy; comparative time studies; energy wood; geometric thinning; pre-commercial thinnings; systematic thinnings
Abstract | View details | Full text in PDF | Author Info
At present, only a small proportion of the potential extractable bioenergy from young dense forests in Sweden is utilized. The conventional mechanized first thinning systems used in such stands suffer from low productivity, so the operation is only profitable in stands with bigger trees and high standing volumes. Conventional harvesters are used for this operation equipped with accumulating felling heads designed for handling several trees during each crane cycle. In thinning from below the felling and bunching work requires many time-consuming non-linear crane movements to avoid felling or damaging of future crop trees. However, higher productivity can be achieved when trees between strip roads are harvested in about 1 m-wide corridors with a length corresponding to the reach of the crane. We refer to this operation as boom-corridor thinning. The objective of this study was to compare felling and bunching productivity in young dense stands when employing thinning from below or boom-corridor thinning. Experiments were performed using a randomized block design involving between 4400 and 18 600 trees x ha-1 with a corresponding average tree size of 7.2 and 3.2 cm dbh, respectively. Based on the average tree being removed at a dbh of 5.7 cm, the productivity (ODt x PW-hour-1) was significant (almost 16%) higher for the boom-corridor thinning than for thinning from below treatment. At the same time, the time taken for the work element “Crane in-between” (the period between the loaded crane starting to move towards a tree and the felling head rapidly slowing down for positioning) was significantly reduced, by almost 17%. The positive results were achieved even though the operator was new to the method. To achieve a significantly higher efficiency during the felling and bunching operation, development of new harvesting equipment and operating techniques seems crucial.
  • Bergström, Swedish University of Agricultural Sciences, Dept of Forest Resource Management, Section of Planning and Operations Management, Umeå, Sweden E-mail: dan.bergstrom@srh.slu.se (email)
  • Bergsten, Swedish University of Agricultural Sciences, Dept of Forest Resource Management, Section of Planning and Operations Management, Umeå, Sweden E-mail: ub@nn.se
  • Nordfjell, Swedish University of Agricultural Sciences, Dept of Forest Resource Management, Section of Planning and Operations Management, Umeå, Sweden E-mail: tn@nn.se
article id 343, category Research article
Karin Vestlund, Tomas Nordfjell, Lars Eliasson, Anders Karlsson. (2006). A decision support system for selective cleaning. Silva Fennica vol. 40 no. 2 article id 343. https://doi.org/10.14214/sf.343
Keywords: forestry; pre-commercial thinning; automation; practical cleaning
Abstract | View details | Full text in PDF | Author Info
Cleaning (pre-commercial thinning) costs have increased relative to logging and regeneration costs, creating a desire for rationalisation. Cleaning with robots may be a solution, but automating stem selections requires a decision support system (DSS) capable of rendering acceptable results. The aims were to develop a DSS for automation of individual stem selections in practical cleaning, and to test, using simulations, if it renders acceptable results. Data on 17 young forest stands were used to develop a DSS that selects stems by species, position (including distance and density parameters), diameter, and damage. Six simulations were run, following the DSS, with different target settings for density, percentage of deciduous stems and minimum distance between stems. The results depend on the initial state of the stands, but generally met the requested targets in an acceptable way. On average, the density results deviated by –20% to +6% from the target values, the amount of deciduous stems shifted towards the target values, and the proportion of stems with defined damaged decreased from initially 14–90% to 4–13%. The mean diameter at breast height increased and the minimum allowed distance between stems was never violated. The simulation results indicate that the DSS is operational. However, for implementation in robotics a crucial problem is to automatically perceive the selected attributes, so additional simulations with erroneous data were run. Correct measurements of diameters are less crucial than to find the majority of the trees and the majority of trees with damages.
  • Vestlund, Swedish University of Agricultural Sciences, Department of Silviculture, P.O. Box 7060, SE-750 07 Uppsala, Sweden E-mail: karin.vestlund@ssko.slu.se (email)
  • Nordfjell, Swedish University of Agricultural Sciences, Department of Forest Resource Management and Geomatics, SE-901 83 Umeå, Sweden E-mail: tn@nn.se
  • Eliasson, Swedish University of Agricultural Sciences, Department of Silviculture, SE-901 83 Umeå, Sweden E-mail: le@nn.se
  • Karlsson, Swedish University of Agricultural Sciences, Department of Silviculture, SE-901 83 Umeå, Sweden E-mail: ak@nn.se
article id 363, category Research article
Karin Vestlund, Tomas Nordfjell, Lars Eliasson. (2005). Comparison of human and computer-based selective cleaning. Silva Fennica vol. 39 no. 4 article id 363. https://doi.org/10.14214/sf.363
Keywords: forestry; decision support; pre-commercial thinning; automation; practical cleaning; training-tool
Abstract | View details | Full text in PDF | Author Info
In silvicultural tending operations like cleaning (pre-commercial thinning), the results are irreversible, so it is important for the decisions to be consistent with the aims for the stand. To enable operational automatic stem selections, a decision support system (DSS) is needed. A previously presented DSS seems to render acceptable cleaning results, but needs further analysis. The aims of the study were to compare the cleaning results of experienced cleaners and DSS simulations when “similar” instructions were given, and to assess the usefulness and robustness of the DSS. Twelve experienced cleaners were engaged to “clean” (mark main stems) six areas; each cleaner “cleaned” two areas. The DSS was used to generate two computer-based cleanings (simulations) of these areas. Four laymen also “cleaned” one of the areas following the DSS. The density results were significantly affected by the areas’ location, whereas the proportions of deciduous stems and damaged stems were significantly affected by both the areas’ location and method, i.e. manual “cleaning” and general or adjusted simulation. The study showed that the DSS can be adjusted so that the results are comparable with the cleaners’ results. Thus, the DSS seems to be useful and flexible. The laymen’s results were close to the results of the “general” simulation, implying that the DSS is robust and could be used as a training tool for inexperienced cleaners. The DSS was also acceptable on a single-tree level, as more than 80% of the main-stems selected in the simulations were also selected by at least one cleaner.
  • Vestlund, Swedish University of Agricultural Sciences, Department of Silviculture, P.O. Box 7060, SE-750 07 Uppsala, Sweden E-mail: karin.vestlund@ssko.slu.se (email)
  • Nordfjell, Swedish University of Agricultural Sciences, Department of Silviculture, SE-901 83 Umeå, Sweden E-mail: tm@nn.se
  • Eliasson, Swedish University of Agricultural Sciences, Department of Silviculture, SE-901 83 Umeå, Sweden E-mail: le@nn.se

Category : Research note

article id 148, category Research note
Ola Lindroos, Magnus Matisons, Petter Johansson, Tomas Nordfjell. (2010). Productivity of a prototype truck-mounted logging residue bundler and a road-side bundling system. Silva Fennica vol. 44 no. 3 article id 148. https://doi.org/10.14214/sf.148
Keywords: bioenergy; compaction; composite residue logs; densification; road-side landing; slash; supply chain
Abstract | View details | Full text in PDF | Author Info
When recovering logging residues (LR) for bioenergy its density should be increased before road transport, otherwise a low proportion of the trucks’ load capacity will be used. One way this can be currently done is to compress LR into bundles that are forwarded to roadside landing. A less well-developed alternative is to forward loose LR and bundle it at landing. In the presented study, a prototype specifically developed for road-side bundling was found to produce larger, heavier bundles than bundling machinery intended for in-field use (mean length, diameter and raw bulk density 4.7 m, 0.8 m and 285 kg m–3, respectively, with 299–445 kg oven dry matter per bundle). The machine was also at least 30% more productive than previously described in-field bundling systems, producing 14–19 bundles per productive work hour (PWh), equivalent to 5.2–7.8 oven-dry tonnes PWh–1. Bundles were estimated to use 67–86% of an LR truck’s 30 tonnes load capacity, similar to proportions used when transporting loose LR. However, a continuous feeding and compressing process would probably almost double productivity, while longer bundles would enable full use of truck load capacity. With such improvements bundling at road-side could provide a viable alternative to current LR-recovering systems.
  • Lindroos, Department of Forest Resource Management, Swedish University of Agricultural Sciences, Umeå, Sweden E-mail: ola.lindroos@srh.slu.se (email)
  • Matisons, Department of Forest Resource Management, Swedish University of Agricultural Sciences, Umeå, Sweden E-mail: mm@nn.se
  • Johansson, Sveaskog Förvaltnings AB, Vindeln, Sweden E-mail: pj@nn.se
  • Nordfjell, Department of Forest Resource Management, Swedish University of Agricultural Sciences, Umeå, Sweden E-mail: tn@nn.se
article id 311, category Research note
Dan Bergström, Urban Bergsten, Tomas Nordfjell, Tomas Lundmark. (2007). Simulation of geometric thinning systems and their time requirements for young forests. Silva Fennica vol. 41 no. 1 article id 311. https://doi.org/10.14214/sf.311
Keywords: bioenergy; forest technology; multi-stem
Abstract | View details | Full text in PDF | Author Info
In Fennoscandia, large areas that have not been subjected to pre-commercial thinning (PCT), and thus support dense stands, are becoming suitable for harvesting biomass. However, efficient systems for harvesting biomass from young stands have not yet been developed. In order to optimise biomass harvesting it is here hypothesized that the handling unit should not be a single tree but a corridor area, i.e., all trees in a specific area should be harvested in the same crane movement cycle. Three types of corridor harvesting approaches (using accumulating felling heads for geometric harvesting in two different patterns) were compared in terms of time required to fell a corridor of standardised size. Corridors are defined as strips of harvested areas between conventional strip-roads. Harvests were simulated in two types of stands, first thinning (FT) and delayed PCT stands, in which the spatial positions of the trees had been mapped. The differences in simulated time consumption per corridor were minor when the only variable changed was the corridor pattern. However, there were ca. 2-fold and 3-fold differences in simulated time consumption per corridor between the harvesting approaches for the FT stand and the PCT-stand, respectively. Furthermore, area handling (felling head accumulating all trees corridor-wise, with no restrictions on the accumulated number of trees except for a certain load limit) was found to give up to 2.4-fold increases in productivity compared to a single-tree (reference) approach for the FT stand. In conclusion, the simulation results clearly show the benefits of applying area-harvesting systems in young, dense stands.
  • Bergström, SLU, Dept. of Forest Resource Management, SE-901 83 Umeå, Sweden E-mail: db@nn.se (email)
  • Bergsten, SLU, Dept. of Forest Ecology and Management, SE-901 83 Umeå, Sweden E-mail: ub@nn.se
  • Nordfjell, SLU, Dept. of Forest Resource Management, SE-901 83 Umeå, Sweden E-mail: tn@nn.se
  • Lundmark, SLU, Vindeln Experimental Forests, Svartberget Field Station, SE-922 91 Vindeln, Sweden E-mail: tl@nn.se
article id 379, category Research note
Daniel Ligné, Lars Eliasson, Tomas Nordfjell. (2005). Time consumption and damage to the remaining stock in mechanised and motor manual pre-commercial thinning. Silva Fennica vol. 39 no. 3 article id 379. https://doi.org/10.14214/sf.379
Keywords: birch; Scots pine; cleaning; time study; brush saw; Husqvarna; Vimek
Abstract | View details | Full text in PDF | Author Info
Selective pre-commercial thinning (PCT) is usually carried out by workers with a brush saw in order to increase the growth of the potential crop trees (main stems) through removal of competing trees. In the last decade relative PCT costs have increased, partly because stands are denser and have higher trees when treated, which has led to new interest for mechanised PCT. The objective was to compare mechanised and motor manual PCT regarding productivity and damage to remaining main stems. Time consumption for, and damage after, mechanised and motor manual PCT were studied on 50 plots per treatment in mixed pine birch stands with an initial stand density exceeding 4500 stems ha–1. In the present study productivity was influenced by stand density, stand height and the quota between height and diameter. Irrespectively of these factors, mechanised PCT was 0.74 hours ha–1 slower than motor manual PCT. Motor manual PCT of the average stand (average height 3.69 m, 10 816 stems ha–1) took 5.06 effective hours. In average 2475 and 2805 main stems ha–1 were left after the mechanised and motor manual treatments, respectively, whereof 1.3 and 2.1% were damaged by the treatments. The results show that efficiency in motor manual PCT has increased in dense and tall stands compared to older studies. Motor manual PCT was more time effective than mechanised PCT, and thereby also even more cost-effective. However, the potential for technical and methodological development of mechanised PCT is probably larger than for motor manual PCT.
  • Ligné, Swedish University of Agricultural Sciences, Department of Silviculture, SE-901 83 Umeå, Sweden E-mail: dl@nn.se
  • Eliasson, Swedish University of Agricultural Sciences, Department of Silviculture, SE-901 83 Umeå, Sweden E-mail: lars.eliasson@norraskogsagarna.se (email)
  • Nordfjell, Swedish University of Agricultural Sciences, Department of Silviculture, SE-901 83 Umeå, Sweden E-mail: tn@nn.se

Register
Click this link to register to Silva Fennica.
Log in
If you are a registered user, log in to save your selected articles for later access.
Contents alert
Sign up to receive alerts of new content
Your selected articles